gcloud beta compute interconnects attachments dedicated create - create a Compute Engine dedicated interconnect attachment
gcloud beta compute interconnects attachments dedicated create NAME --interconnect=INTERCONNECT --router=ROUTER [--bandwidth=BANDWIDTH] [--candidate-ipv6-subnets=[IPV6_SUBNET,...]] [--candidate-subnets=[SUBNET,...]] [--cloud-router-ipv6-interface-id=INTERFACE_ID] [--customer-router-ipv6-interface-id=PEER_INTERFACE_ID] [--description=DESCRIPTION] [--enable-admin] [--mtu=MTU] [--region=REGION] [--stack-type=STACK_TYPE] [--vlan=VLAN] [GCLOUD_WIDE_FLAG ...]
(BETA) gcloud beta compute interconnects attachments dedicated create is used to create a dedicated interconnect attachments. An interconnect attachment is what binds the underlying connectivity of an interconnect to a path into and out of the customer's cloud network.
- NAME
Name of the interconnect attachment to create.
- --interconnect=INTERCONNECT
The interconnect for the interconnect attachment
- --router=ROUTER
The Google Cloud Router to use for dynamic routing.
- --bandwidth=BANDWIDTH
Provisioned capacity of the attachment. BANDWIDTH must be one of:
- 50m
50 Mbit/s
- 100m
100 Mbit/s
- 200m
200 Mbit/s
- 300m
300 Mbit/s
- 400m
400 Mbit/s
- 500m
500 Mbit/s
- 1g
1 Gbit/s
- 2g
2 Gbit/s
- 5g
5 Gbit/s
- 10g
10 Gbit/s
- 20g
20 Gbit/s
- 50g
50 Gbit/s
- --candidate-ipv6-subnets=[IPV6_SUBNET,...]
Up to 16 candidate prefixes that control the allocation of cloudRouterIpv6Address and customerRouterIpv6Address for this attachment. Each prefix must be in the Global Unique Address (GUA) space. It is highly recommended that it be in a range owned by the requestor. A GUA in a range owned by Google will cause the request to fail. Google will select an available prefix from the supplied candidates or fail the request. If not supplied, a /125 from a Google-owned GUA block will be selected.
- --candidate-subnets=[SUBNET,...]
Up to 16 candidate prefixes that can be used to restrict the allocation of cloudRouterIpAddress and customerRouterIpAddress for this attachment. All prefixes must be within link-local address space. Google will attempt to select an unused /29 from the supplied candidate subnet(s), or all of link-local space if no subnets supplied. Google will not re-use a /29 already in-use by your project, even if it's contained in one of the candidate subnets. The request will fail if all /29s within the candidate subnets are in use at Google's edge.
- --cloud-router-ipv6-interface-id=INTERFACE_ID
If supplied, the interface id (index within the subnet) to be used for the Cloud Router address. The id must be in the range of 1 to 6. If a subnet mask is supplied, it must be /125, and the subnet should either be 0 or match the selected subnet.
- --customer-router-ipv6-interface-id=PEER_INTERFACE_ID
If supplied, the interface id (index within the subnet) to be used for the Cloud Router address. The id must be in the range of 1 to 6. If a subnet mask is supplied, it must be /125, and the subnet should either be 0 or match the selected subnet.
- --description=DESCRIPTION
Human-readable plain-text description of attachment.
- --enable-admin
Administrative status of the interconnect attachment. If not provided on creation, defaults to enabled. When this is enabled, the attachment is operational and will carry traffic. Use --no-enable-admin to disable it.
- --mtu=MTU
Maximum transmission unit (MTU) is the size of the largest IP packet passing through this interconnect attachment. Only 1440 and 1500 are allowed values. If not specified, the value will default to 1440.
- --region=REGION
Region of the interconnect attachment to create. If not specified, you might be prompted to select a region (interactive mode only).
To avoid prompting when this flag is omitted, you can set the compute/region property:
$ gcloud config set compute/region REGION
A list of regions can be fetched by running:
$ gcloud compute regions list
To unset the property, run:
$ gcloud config unset compute/region
Alternatively, the region can be stored in the environment variable CLOUDSDK_COMPUTE_REGION.
- --stack-type=STACK_TYPE
The stack type of the protocol(s) enabled on this interconnect attachment. STACK_TYPE must be one of:
- IPV4_IPV6
Both IPv4 and IPv6 protocols are enabled on this attachment.
- IPV4_ONLY
Only IPv4 protocol is enabled on this attachment.
- --vlan=VLAN
Desired VLAN for this attachment, in the range 2-4093. If not supplied, Google will automatically select a VLAN.
These flags are available to all commands: --access-token-file, --account, --billing-project, --configuration, --flags-file, --flatten, --format, --help, --impersonate-service-account, --log-http, --project, --quiet, --trace-token, --user-output-enabled, --verbosity.
Run $ gcloud help for details.
This command is currently in beta and might change without notice. These variants are also available:
$ gcloud compute interconnects attachments dedicated create
$ gcloud alpha compute interconnects attachments dedicated create